![]() Issue Kermit send command from thereĬ5000_xx.bin => C5000_XX.BIN, Size: 1233266 Return to your local Machine by typing its escape sequence Type the escape character followed by C to get back,Ĭonsole> (enable) set system baud 19200 ^\Cĭownload Supervisor image via console port (y/n) ? y Following is a sample session showing a connection to a remote terminal from a Sun workstation and the use of the download serial command to copy a software image to the supervisor card:Ĭ-Kermit 5A(172) ALPHA, 30 Jun 95, SUNOS 4.0 (BSD) In the following example, a tty port is connected to the command-line interface port on theĬatalyst 5000 series switch. This command will interrupt the download process and could leave the switch in a problematic state. The download serial command is not allowed from a Telnet session.Ĭaution After starting the serial download using Kermit, do not attempt to abort the serial download by using Ctrl-C. This command uses the Kermit protocol through the serial EIA/TIA-232 console port. ![]() This command has no arguments or keywords. Use the download serial privileged command to copy software images to the supervisor card or Flash memory through a serial port. The following example shows how to download the acpflash_1111.bbi code from the mercury host:Ĭonsole> (enable) download mercury acpflash_1111.bbi 3ĭownload image acpflash_1111.bbi from mercury to Module 3 FLASH (y/n) ? yĭone. The following example shows how to download the fddi_1113.cpi code from the mercury host:Ĭonsole> (enable) download mercury fddi_1113.cpi 4ĭownload image fddi_1113.cbi from mercury to Module 4 FLASH (y/n) ? yįinished network download. Programming Flash: Flash Programming CompleteĮrase(b=2, c=4): block(s): 2 3 4 5 Erase done The following example shows how to download the c5000_spv11.bin file from the mercury host:Ĭonsole> (enable) download mercury c5000_spv11.binĭownload image c5000_spv11.bin from mercury to module 1FLASH (y/n) ? yĭone. To download a software image for the RSM, use the session command. When downloading to the ATM module, the supervisor module acts as a Trivial File Transfer Protocol (TFTP) gateway, forwarding TFTP packets to the ATM module through an in-band interprocessor communication (IPC) method. Catalyst 5000 series software rejects an image if it is not a valid image for the module. The download command downloads code to the module Flash memory. The ATM module has processors that will require field upgrades. Only the first applies to the Asynchronous Transfer Mode (ATM) module. The Catalyst 5000 series switches support two ways to download new code to the processors: TFTP network download through any network port, and Kermit serial download through the EIA/TIA-232 console port. If a module number is not specified, the image is downloaded to all modules for which the image is valid. (Optional) Number of the module to receive downloaded image. download host file Syntax Description host Use the download privileged command to copy a software image from a specified host to the Flash memory of a designated module. Telnet session from 198.134.214.4 disconnected. The following example shows how to close a Telnet session with a host and how to close the current console session:Ĭonsole> (enable) disconnect 198.134.214.4 You can answer n and remain connected or answer y and be disconnected. The system prompts whether to disconnect the current Telnet session. If it is, all sessions, other than the current session, are disconnected. If it is not, all Telnet sessions from the specified IP address are disconnected. If multiple sessions from the same IP address exist, the disconnect command checks if the current process is also from the same IP address. Use the configure privileged command to download a configuration file from the network and execute each command in that file. show commands are described in the " ATM show Commands" chapter configure.General commands are described in the " General ATM Commands" chapter.show commands are described in the " Switch show Commands" chapter.set commands are described in the " Switch set Commands" chapter.clear commands are described in the " Switch clear Commands" chapter.Other commands are described elsewhere in this publication: For more information about using the switch CLI, refer to the " Switch Command-Line Interface" chapter. For a summary of the available switch CLI commands, refer to the " Switch Command Quick Reference" chapter. This chapter describes the general commands used in the Catalyst 5000 series switch command-line interface (CLI).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |